There are many types of siding available for your home. Cement board house siding is one of the most durable siding options. It has the ability to withstand extreme cold, rain and wind. It is also non-pest-friendly. This makes it an ideal choice for Fort Worth's TX home.
There are two types main cement boards. The first type is made from Portland cement. The second is made from a combination of cement fibers and plant fibers. These fibers give board its strength and flexibility. The fibers undergo pulverization in water and are then mixed with a variety if additives. A cement fiber board typically contains between 8 and 60 percent cellulose, along with twenty to thirty percent of cement fillers.
Use screws if installing a cement board on top of a steel frame or wood. You'll want to use screws that have a ring shank for strength. It is important that screws are flush to the surface. You should also ensure that the screws are not too deep to weaken the board's hold.
It is important to ventilate your cement board construction before installing it. If you have too little airflow, you'll have mold problems. If you're installing the board in a place where it'll be exposed to moisture, you'll need to apply a waterproofing layer behind the board. To keep water out, you can also install a vapor barrier. You can purchase these materials at your local hardware store.
Before you install your cement board, measure your room. You should leave at minimum a quarter inch of space between each board piece to allow for heat expansion. To determine the measurements, you can use a drywall square. The board must be installed over thin layers of adhesive mortar.
After installing the cement board, seal the joints with silicone caulk. This will prevent any leaks. The board can be attached to the wall using a drywall screws. It is recommended to pre-drill all fasteners. You can also use a round shank nail if you don’t have a drill bit.
Installing your board over brick or tile will require you to use a backer. It will help prevent the tiles breaking. A water-resistant compound is also required to prevent the tiles moving. This is especially important if you plan to expose the tiles to moisture. If your space is subject to water spray or showers, you will need to waterproof it. If you plan to install the cement board onto a floor, you may also need a vapor barrier. To attach the board to the floor, you can use a drywall screw with a ring shank nail.
A grinder and a circular saw are required for cutting cement board. You'll also need a carbide tipped blade. It's best to cut the board in a well-ventilated area. This will help avoid the skunky smell that comes from cutting the cement board.
FAQ
What can I do to save money on my home's renovation?
You can save some money by doing as much of the work yourself as possible. Consider reducing the number or people that you employ during renovations. It is also possible to cut down on the cost of materials during renovations.
How can I avoid being ripped off while renovating my home?
The best way to avoid being ripped off is to know what you are paying for. Be sure to read the fine print before you sign any contract. Also, don't sign blank contracts. Always request copies of signed contracts.
What should you consider when buying your next home?
You should ensure that you have sufficient funds to cover the closing costs of your new home before purchasing it. Refinancing your loan is an option if cash is tight.
Statistics
- ‘The potential added value of a loft conversion, which could create an extra bedroom and ensuite, could be as much as 20 per cent and 15 per cent for a garage conversion.' (realhomes.com)
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
- Most lenders will lend you up to 75% or 80% of the appraised value of your home, but some will go higher. (kiplinger.com)
- On jumbo loans of more than $636,150, you'll be able to borrow up to 80% of the home's completed value. (kiplinger.com)
External Links
How To
How do I plan for a whole house renovation?
Planning a whole house remodel requires careful planning and research. Before you start your project, there are many factors to consider. First, you must decide what type of home improvement you want. You can choose from a variety of categories, such as kitchen or bathroom, bedroom, living space, or living room. Once you've chosen the category you want, you need to decide how much money to put towards your project. If you are new to working in homes, budget at least $5,000 for each room. You might be able get away with less if you have previous experience.
Once you have established how much you are able to afford, you will have to decide on how big a job to do. A small kitchen remodel will not allow you to install new flooring, paint the walls, or replace countertops. On the other side, if your budget allows for a full renovation of your kitchen, you'll be able do just about any task.
Next, you need to find a contractor who is experienced in the type project that you want. This will ensure you get quality results and save you a lot of hassle later. You should begin gathering materials and supplies after you've found a competent contractor. You may need to purchase everything from scratch depending on the size and scope of your project. However, it is possible to find everything you need in a variety of shops that sell premade items.
Now it's time for you to start planning. Begin by sketching out a rough plan of where furniture and appliances will be placed. The next step is to design the layout of the rooms. You should leave enough space for electrical outlets and plumbing. Visitors will be able to easily reach the areas that are most frequently used near the front doors. Final touches to your design include choosing the right colors and finishes. To save money and keep your budget low, you should stick to neutral tones.
Now it's time for you to start building. Before you begin construction, it's important to check your local codes. Some cities require permits while others allow homeowners to build without one. Before you can begin construction, remove any walls and floors. The next step is to lay plywood sheets on your new flooring. Next, nail or screw pieces of wood together to form the frame that will house your cabinets. Finally, attach doors and windows.
After you're done, there are still a few things you need to do. You'll likely want to cover any exposed wires and pipes. For this, you will use plastic sheeting or tape. Also, you will need to hang mirrors or pictures. Just remember to keep your work area clean and tidy at all times.
These steps will help you create a functional, beautiful home that is both functional and attractive. Now that your house renovation plan is in place, you can get started.